J&L metrology optical comparator the original jones and lamsom optical comparator
optical comparator homeoptical comparator productsoptical comparator servicesoptical comparator tech supportOptical Comparatoroptical comparator contactoptical comparator

optical comparator Universal Base Stage
     AC-2774

optical comparator V-Block Stage

optical comparator Centers & Center Blocks

optical comparator Fixture Base

optical comparator Vise Stage AC-2430

optical comparator Electronics Parts Stage
     AC-3818

optical comparator Right-Angle Base AC-2784

optical comparator Screw machine Products
     Stage AC- 3435

optical comparator Flat Work Stage with
     Swivel Base AC-3070

optical comparator Square Tool Stage
     AC-2510

optical comparator Constant Centerline
     V-Block AC-2970

optical comparator Supplementary Fixture
     Bases Single or
     Matched Pairs

optical comparator Jeweler’s Chuck AC-2099

optical comparator Vertically Adjustable
     V-Block Stage AC-3849

optical comparator Universal V-Block Stage
     AC-3021 (Constant
     Center line)

 

optical comparator Back to Products

 

Fixtures

We welcome the unusual. If you require an Optical Comparator fixture unlike anything shown here, J&L Metrology will design it. J&L Metrology is continually developing new work-holding fixtures for your Optical Comparator to keep pace with its unsurpassed line of optical comparators. These high-quality accessories enable you to take full advantage of the measuring and inspection capabilities of your optical comparator. These standard fixtures cover a broad range of requirements. However, special ones designed for your particular application sometimes prove more effective and economical. But whatever you require J&L Metrology can help.

Universal Base Stage AC-2774

This fixture rapidly positions small parts for inspection of various angels and surfaces where no permanent set up is required. By substituting a tool stage for a vise, this fixture can be converted to a universal carbide tool holder. The universal base stage may be used with the optional vise (AC-3873), tool block (33412) or electronic parts stage (AC-3818). The top surface of this base is 3-5/16" diameter.

Note: This base stage does not include the vise.

Optical Comparator

V-Block Stage

This V-Block stage, for staging cylindrical parts on the outside diameter, is available in 1",2",3" and 4" capacities. Matched pairs of these stages are also available in 1",2",3" and 4" capacities.

Note: Clamps are included in all sizes.

#
Singles
#
Matched Pairs
A=Base Height
B= Base Width
1"
AC-2197
1"
AC-2453
2.040
2.187
2"
AC-2210
2"
AC-2454
2.440
3.000
3"
AC-2216
3"
AC-2455
3.140
3.250
4"
AC-2240
4"
AC-2456
3.970
5.187
Optical Comparator

Centers and Center Blocks

These centers and center blocks can be supplied in 3",5" and 8" capacities for staging various diameter parts. The centers are carbide tipped for long life. Female centers are available in hi-speed steel.

#
Male Centers & center blocks
Female Centers & center blocks
1.645
3" max working diameter
AC-2855
3" max working diameter
AC-3094
2.643
5" max working diameter
AC-2854
5" max working diameter
AC-3095
4.272
8" max working diameter
AC-2856
8" max working diameter
AC-3096
Optical Comparator

Fixture Base

This base can be machined to accommodate various forms of holding fixtures. It is finished on the bottom and equipped with hold-down screws. 1", 2", 3", 4", 5" and 6" sizes.

1"
AC-2468
4"
AC-2146
2"
AC-2114
5"
AC-2186
3"
AC-2145
6"
AC-2266

Optical Comparator

Vise Stage AC-2430

This stage is used for staging small parts when no permanent setup is necessary.

The vise can be set either parallel with, or at right angles to the table grooves, and special jaws can be used for staging irregular shapes. This vise stage includes (AC-3873) vise.

Optical Comparator

Electronics Parts Stage AC-3818

The electronics part stage is a versatile holding device for small, delicate parts. Vee notched fingers securely clamp round or flat parts. The vise swivels, slides and tilts in order to present in order to present three or more views of the part.

Fast accurate alignment is accomplished optically on the comparator.

Note: This part stage does not include the universal base stage.

Optical Comparator

Right-Angle Base AC-2784

A convenient accessory to any comparator, for locating fixtures at right angels to the normal position.

Optical Comparator

Screw machine Products Stage AC- 3435

The screw machine products stage is a fixture upon which two adjustable V-Blocks are clamped. The blocks containing large and small vees can be adjusted for various diameters and length on a wide variety of screw machine products. Adjustment is accomplished optically on the comparator.

Optical Comparator

Flat Work Stage with Swivel Base AC-3070

This fixture is used for staging flat form tools or production parts with irregular surfaces. The locating blocks can be adjusted across the width of the fixture and the fixture can be rotated 360deg. Thus presenting any desired angle before the projection lens. The locating jaws may be equipped with false jaws of any profile to hold pieces of irregular shape.

Optical Comparator

Square Tool Stage AC-2510

This fixture provides hardened and ground locating surfaces at right angels to one another, to which parts to be inspected can be accurately aligned.

Optical Comparator

Constant Centerline V-Block AC-2970

This V-Block stage is used for staging cylindrical parts with varying diameters, to maintain readings from the centerline, may be used on all standard comparators. This stage has a capacity range of 1/4" to 2" diameters. Rapid focusing adjustment is provided in the fixture base.

Note: Clamp is included with this fixture.

Optical Comparator

Supplementary Fixture Bases Single or Matched Pairs

These 2 or 3" risers are used when it is necessary to elevate fixtures( such as centers, V-Blocks, vise stages, etc.) above the table. Available singly or as matched pairs. dimensions of the top working surface are 6" long by 4 9\16" wide for the 3" riser and 7 1\4" long by 5 1\4 wide for the 2" versions.

Note: Universal Base is not included with risers.

Singles
Matched Sets
2"
AC-3665
2"
AC-3666
3"
AC-2198
3"
AC-2457

Optical Comparator

Jeweler’s Chuck AC-2099

This chuck is used with other fixtures, such as V-Blocks, for staging small cylindrical parts. Capacity 1/4" max. .010 min. Shank dia. is 7/8".

Optical Comparator

Vertically Adjustable V-Block Stage AC-3849

This versatile fixture features a vertically adjustable VBlock holder to allow a fixed table height. The V-Block may be mounted either vertically or horizontally in the holder plate. Three sides of the base have been tapped to accept the holder plate in various positions for staging difficult parts.

Note: Clamp is included

Optical Comparator

Universal V-Block Stage AC-3021 (Constant Center line)

This adjustable V-Block and clamping fixture is for staging and projecting over the top of cylindrical parts. Capacities from 1/16" to 2" diameters. An adjustable end stop is provided to locate the piece horizontally.

Optical Comparator

 


Privacy Policy                         optical comparator                         Terms of Use

© 2011  J&L Metrology, Inc. – Springfield, VT USA. All Rights Reserved

Web Site Designed by William Mahony Designs